Grass-valley KALEIDO-IP X300 v.7.80 Manuel d'utilisateur

Quick Start GuideM926-9905-1172015-05-29KALEIDO-IP X300 KALEIDO-IP X100HIGH QUALITY IP VIDEO MULTIVIEWERS

xNotices• EN 61000-3-2 Limits for harmonic current emissions• EN 61000-3-3 Limitation of voltage fluctuations and flicker• EN 61000-4-2 Electrostatic

xi1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Overview. . . . . . . . . . . . . . . . . .

1IntroductionWelcome to the Kaleido family of multiviewers! This chapter provides information about system requirements, and items shipped with your

2IntroductionGetting Organizedspecified transport stream information, you can start using these layouts to monitor television signals distributed over

3Kaleido-IP X300/X100Quick Start GuideSystem Requirements for a Client PCA client PC or laptop meeting the following requirements is required to acces

5Setting Up the Kaleido-IPThis chapter will guide you through the installation of a Kaleido-IP X300, or Kaleido-IP X100 multiviewer in its default co

6Setting Up the Kaleido-IPPhysical Setup4 Connect one of the DisplayPort output of the multiviewer to a display that supports a resolution of 1920 × 1

7Kaleido-IP X300/X100Quick Start GuideCabling DiagramCabling diagram for a Kaleido-IP X100 or X300 with two network adapters. The Kaleido-IP X300 mode

iiNoticesCopyright & Trademark NoticeCopyright © 2011–2015, Grass Valley USA, LLC. All rights reserved.Belden, Belden Sending All The Right Signal

8Setting Up the Kaleido-IPNetworking Setup3Clear the Use detected monitor resolution check box.4 Select the desired resolution from the Default DVI re

9Kaleido-IP X300/X100Quick Start GuideThe Kaleido-IP is shipped with the following default settings.To change the Kaleido-IP’s management and data IP

10Setting Up the Kaleido-IPNetworking Setup4 Click the XAdmin button.5 If you see a security warning, or a certificate error message, then refer to Re

11Kaleido-IP X300/X100Quick Start Guide9Under General, type a different name for your system if you wish.If there are more than one multiviewer in the

12Setting Up the Kaleido-IPNetworking Setup11 Under Date and Time, select the appropriate time zone and format for your location.12 If this Kaleido-IP

13Kaleido-IP X300/X100Quick Start GuideaClick Configure, under DNS and proxy configuration. The DNS and Proxy Configuration page appears.b Type the ap

14Setting Up the Kaleido-IPNetworking SetupChanging an IP Address on Windows 7 or Windows 8To change the IP address of a client PC that has Windows 7

15Kaleido-IP X300/X100Quick Start Guide6 Type an IP address in the same range as the multiviewer’s current IP address.For example, if the multiviewer’

16Setting Up the Kaleido-IPXEdit InstallationStep 3: XEdit InstallationXEdit is a client application used to create layouts for the monitor wall, and

17Kaleido-IP X300/X100Quick Start GuideAt the end of the installation process:• If you have Windows 7, or Windows XP, shortcuts ( ) are added to your

iiiKaleido-IP X300/X100Quick Start GuideImportant Safeguards and NoticesThis section provides important safety guidelines for operators and service pe

18Setting Up the Kaleido-IPXEdit InstallationDepending on your Windows Firewall settings, a security alert may appear.•Click Allow access to unblock t

19Kaleido-IP X300/X100Quick Start GuideFor more information about calibrating your system, configuring rooms, creating layouts, and operating the moni

20Setting Up the Kaleido-IPSystem SetupOpening XEdit in Online ModeTo open XEdit in online mode1 From a workstation on the same subnet as the multivie

21Kaleido-IP X300/X100Quick Start GuideThe settings for the selected multicast stream appear in the Properties pane.3 Replace the default stream name

22Setting Up the Kaleido-IPSystem SetupThe Kaleido-IP establishes a connection with the selected stream. All programs that are part of the stream, and

23Kaleido-IP X300/X100Quick Start GuideRefer to Managing Transport Streams in a Kaleido-IP System Representation, in the Kaleido-X User’s Manual, for

24Setting Up the Kaleido-IPSystem Setup4 If the stream you wish to add is constrained to a virtual LAN, select Virtual LAN tagging, and then type the

25Kaleido-IP X300/X100Quick Start GuideAdding a Unicast Transport StreamTo add a unicast transport stream1 In the main window, click the System tab, a

26Setting Up the Kaleido-IPTesting the Monitor Wall Operation2In the Tools pane, expand the multiviewer, and navigate to the transport stream for whic

27Kaleido-IP X300/X100Quick Start GuideTo start using the Kaleido-RCP2 with its default settings1 Physically connect the Kaleido-RCP2 unit to the mana

ivNoticesWarningsA warning indicates a possible hazard to personnel, which may cause injury or death. Observe the following general warnings when usin

28Setting Up the Kaleido-IPTesting the Monitor Wall OperationThe message “Access granted” will appear on the LCD display if the login is successful. I

29SpecificationsKaleido-IP InputsIP INPUTS Physical 2 Gigabit Ethernet with RJ-45 connector (MGMT and DATA)2 or 4 additional data Gigabit Ethernet wi

30SpecificationsKaleido-IP Display OutputsThe Kaleido-IP supports two independently configurable and operable progressive scan display outputs.Kaleido

31Kaleido-IP X300/X100Quick Start GuideOperation and ConfigurationDisplay Output Extender via Fiber OpticMax. storage humidity 90% RH non-condensingMa

33Disposal and Recycling Information Your Grass Valley equipment comes with at least one lithium button battery (Li-MnO2) located on the main printed

34Disposal and Recycling Information4 Dispose of the battery and equipment according to your local environmental laws and guidelines.For more informat

Contact UsGrass Valley Technical SupportFor technical assistance, contact our international support center, at 1-800-547-8949 (US and Canada) or +1 53

vKaleido-IP X300/X100Quick Start Guide• When installing this equipment, do not attach the power cord to building surfaces.• Products that have no on/o

viNoticesMesures de sécurité et avis importantsLa présente section fournit des consignes de sécurité importantes pour les opérateurs et le personnel d

viiKaleido-IP X300/X100Quick Start GuideAvertissementsLes avertissements signalent des conditions ou des pratiques susceptibles d’occasionner des bles

viiiNotices• Après tout travail d’entretien ou de réparation, faites effectuer des contrôles de sécurité par le personnel technique qualifié.Mises en

ixKaleido-IP X300/X100Quick Start Guide• Pour plus de sécurité, vérifiez périodiquement la valeur de résistance du bracelet antistatique. Elle doit se