Grass-valley M-2100 Manuel d'utilisateur

MINI MASTER CONTROL PANEL M-2100 DIGITAL MASTER CONTROL SYSTEMInstallation and Operation0718129005.0software releaseFIRST PRINTING: JULY 2001

1-2 MMCP Installation/Operation ManualSection 1 — Installation Control Panel Installation The MMCP Control Panel can be installed in the following wa

MMCP Installation/Operation Manual 1-3Control Panel Installation Figure 1-3. Front and Right Side Panel Dimensions Tabletop Mounting The MMCP panel

1-4 MMCP Installation/Operation ManualSection 1 — Installation Console Mounting A mounting bracket option kit provides a console mounting bracket to

MMCP Installation/Operation Manual 1-5Control Panel Installation Rack Mounting To mount the control panel in a standard 19 in. (483 mm) rack, use the

1-6 MMCP Installation/Operation ManualSection 1 — Installation Control Panel Cabling The connections to the MMCP panel are made at the rear of the p

MMCP Installation/Operation Manual 1-7Control Panel Cabling Power Supply Alarms A 9-pin male connector at J1 provides a power supply status reporting

1-8 MMCP Installation/Operation ManualSection 1 — Installation Network Configuration The MMCP communicates with the M–2100 frames over a separate MCP

MMCP Installation/Operation Manual 1-9Control Panel Cabling Use the following procedure to set the IP address using the Netburner PC tool. 1. Connect

1-10 MMCP Installation/Operation ManualSection 1 — Installation Direct PC Connection You may use a PC equipped with an Ethernet interface and a web b

MMCP Installation/Operation Manual 1-11Control Panel Cabling 4. In the Boot Configuration screen (Figure 1-12 on page 1-11), enter the Ethernet IP a

Contacting Grass Valley Group Copyright © Grass Valley Group. All rights reserved.This document may not be copied, in whole or in part, or otherwise

1-12 MMCP Installation/Operation ManualSection 1 — Installation Control Panel Configuration After installing the panel in the MCP Net and in its opera

MMCP Installation/Operation Manual 1-13Control Panel Cabling Figure 1-13. MMCP Configuration

1-14 MMCP Installation/Operation ManualSection 1 — Installation Control Panel Diagnostics Some control panel diagnostics are available through the D

MMCP Installation/Operation Manual 1-15Control Panel CablingFigure 1-14. MMCP Diagnostics Screen

1-16 MMCP Installation/Operation ManualSection 1 — InstallationSoftware Installation The MMCP requires that the M–2100 is running v5.0 or later softwa

MMCP Installation/Operation Manual 2-1Section 2System OperationsAbout this SectionThis section of the Mini Master Control Panel Installation and Opera

2-2 MMCP Installation/Operation ManualSection 2 — System OperationsIntroductionThe Mini Manual Control Panel shown in Figure 2-1, provides an alterna-

MMCP Installation/Operation Manual 2-3Using Multichannel ControlUsing Multichannel ControlA powerful feature of the M–2100 is the ability to control m

2-4 MMCP Installation/Operation ManualSection 2 — System OperationsThe Channel Control button color, tally states and their meanings are summa-rized i

MMCP Installation/Operation Manual 2-5Using Multichannel Control2. Press and hold down one unassigned Channel Control button whose button state is off

MMCP Installation/Operation Manual iii Contents Preface About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-6 MMCP Installation/Operation ManualSection 2 — System OperationsAssigning Primaries and SecondariesAny button that is displaying dim green status m

MMCP Installation/Operation Manual 2-7Using Multichannel ControlAutomation Enable The Channel Control buttons are also used to enable/disable automati

2-8 MMCP Installation/Operation ManualSection 2 — System OperationsProgram and Preset Bus OperationsPreset BusThe Preset bus (PST) (Figure 2-4) is a r

MMCP Installation/Operation Manual 2-9Program and Preset Bus OperationsIf video and audio monitors have been connected, you can view, hear, and adjust

2-10 MMCP Installation/Operation ManualSection 2 — System OperationsSources active on the Program bus are sent to the Program output. This is typicall

MMCP Installation/Operation Manual 2-11Program and Preset Bus OperationsIf a particular input has been configured as a Router Linked Destination, the n

2-12 MMCP Installation/Operation ManualSection 2 — System OperationsTransition Controls and OperationA transition is a change from one combination of

MMCP Installation/Operation Manual 2-13Transition Controls and OperationFrom left to right, the Transition Type buttons select: Take — provides a cle

2-14 MMCP Installation/Operation ManualSection 2 — System OperationsIf the hot cut is performed on a crosspoint configured with a preroll enabled, the

MMCP Installation/Operation Manual 2-15Transition Controls and OperationUsing Custom TransitionsHaving previously defined your custom transitions using

iv MMCP Installation/Operation ManualContents Transition Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-16 MMCP Installation/Operation ManualSection 2 — System OperationsIf a selected Transition Type has been defined as custom, the following data will b

MMCP Installation/Operation Manual 2-17Transition Controls and OperationAudio/Video BreakawaysTransitions can be tailored to change only selected sign

2-18 MMCP Installation/Operation ManualSection 2 — System OperationsBreakaway Selection ExamplesAudio Only Breakaway Example #11. Select VTR2 on Prese

MMCP Installation/Operation Manual 2-19Transition Controls and OperationNext Transition ButtonsThe Next Transition buttons (Figure 2-7) select whether

2-20 MMCP Installation/Operation ManualSection 2 — System OperationsHolding the Key button down can have special effects, as described in Cutting Keys

MMCP Installation/Operation Manual 2-21Transition Controls and OperationSecond Press (and Subsequent) TransitionsDuring a preroll, a repeat press of t

2-22 MMCP Installation/Operation ManualSection 2 — System OperationsGPI ButtonsTwo user-configurable buttons, GP I1 and GPI 2, (Figure 2-9) allow contr

MMCP Installation/Operation Manual 2-23Mode/Function ButtonMode/Function ButtonThe Mode/Function button (Figure 2-10) is a multi-purpose control used

2-24 MMCP Installation/Operation ManualSection 2 — System OperationsKeyer Controls and OperationThe Keyer Control subpanel (Figure 2-11) offers contro

MMCP Installation/Operation Manual 2-25Keyer Controls and OperationKey modifiers are available to add borders whose luminance parameter can be adjusted

MMCP Installation/Operation Manual vContents Audio Breakaway Audio (ABA) Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44Left an

2-26 MMCP Installation/Operation ManualSection 2 — System OperationsSelecting and Transitioning KeysAny combination of keyers (from 1 to all 4 keyers)

MMCP Installation/Operation Manual 2-27Keyer Controls and Operation3. The key cuts on or off air.Previewing the KeyAs long as the key signal is synchr

2-28 MMCP Installation/Operation ManualSection 2 — System OperationsKey Modifier Mode DefinitionKey modifier mode is defined by one of the following condi

MMCP Installation/Operation Manual 2-29Keyer Controls and Operation2. Adjust the matte using the Brightness, Hue, and Saturation potentiometers (while

2-30 MMCP Installation/Operation ManualSection 2 — System OperationsBorder (Brdr) ButtonThe Brdr button (Figure 2-11 on page 2-24) is operable if the

MMCP Installation/Operation Manual 2-31Keyer Controls and OperationKey Modifier Button Tally SummaryKey Modifier KnobsHue, Saturation and BrightnessThe

2-32 MMCP Installation/Operation ManualSection 2 — System Operations2. Press a Key Select button. All setup buttons and knobs associated with that key

MMCP Installation/Operation Manual 2-33Keyer Controls and OperationSetting Matte ConfigurationsThe following matte settings are configured at the MMCP:

2-34 MMCP Installation/Operation ManualSection 2 — System OperationsConfiguring the Loss Of Signal (LOS) MatteIf an on-air source is lost, the Loss Of

MMCP Installation/Operation Manual 2-35Keyer Controls and OperationUsing SqueezeBack and CropSqueezeBack and Crop are special key-type effects used in

vi MMCP Installation/Operation ManualContents

2-36 MMCP Installation/Operation ManualSection 2 — System OperationsYou can store up to four SqueezeBack/Crop effects. The four effects (num-bered 1,

MMCP Installation/Operation Manual 2-37Keyer Controls and OperationSelecting and Displaying SqueezeBack EffectsTo select a SqueezeBack effect:1. Press

2-38 MMCP Installation/Operation ManualSection 2 — System OperationsCreating Chroma KeysThe optional Chroma Keyer Module (2100-CKM) may be configured i

MMCP Installation/Operation Manual 2-39Keyer Controls and OperationAuto Setup ModeThe auto setup mode is used to graphically select a color to suppres

2-40 MMCP Installation/Operation ManualSection 2 — System OperationsUsing Auto SetupFollow the instructions given below to use Auto Setup. Depending o

MMCP Installation/Operation Manual 2-41Audio Controls and OperationAudio Controls and OperationThis section covers the controls and operation of the A

2-42 MMCP Installation/Operation ManualSection 2 — System OperationsAudio Processor Delegation Audio Processor 1 (AP 1), the standard audio processor,

MMCP Installation/Operation Manual 2-43Audio Controls and OperationHigh tally is a push-and-hold function. If any selection or adjustment is made on e

2-44 MMCP Installation/Operation ManualSection 2 — System OperationsAudio Breakaway OperationsIf the Audio Only button in the Breakaway section has be

MMCP Installation/Operation Manual 2-45Audio Controls and OperationIf the desired crosspoint is in the Audio Control subpanel, select the Audio Only b

MMCP Installation/Operation Manual vii Preface About This Manual This manual provides control panel installation and operating information for the Gr

2-46 MMCP Installation/Operation ManualSection 2 — System OperationsLeft and Right (Audio) ButtonsThere are two sets of Left and Right buttons (Figure

MMCP Installation/Operation Manual 2-47Audio Controls and Operationbutton will flash. Also note that phase invert is effective only in Stereo mode, so

2-48 MMCP Installation/Operation ManualSection 2 — System OperationsThe level associated with an Only source is effective when the Only source is used

MMCP Installation/Operation Manual 2-49Audio Controls and OperationThe Primary/Over LED display shows the ratio of an Over to the Primary on either th

2-50 MMCP Installation/Operation ManualSection 2 — System OperationsAudio Ratio ProfilesThis section describes how Overs are transitioned to the Progra

MMCP Installation/Operation Manual 2-51Audio Controls and OperationCut Transition—Cut out Over onlyConditions: No change in audio Main sources Over

2-52 MMCP Installation/Operation ManualSection 2 — System OperationsAt the effective time of the transition cut (considering preroll, transition hold

MMCP Installation/Operation Manual 2-53Audio Controls and OperationHot Cut Transition 3Conditions: Hot cut: Remove an Over on the Program bus by pres

2-54 MMCP Installation/Operation ManualSection 2 — System OperationsAudio Monitor SubpanelThe Audio Monitor subpanel (Figure 2-14) provides control of

MMCP Installation/Operation Manual 2-55Audio Controls and OperationThe monitor levels are associated with the monitor, and not the Audio Pro-cessor, n

viii MMCP Installation/Operation ManualPreface

2-56 MMCP Installation/Operation ManualSection 2 — System Operations

MMCP Installation/Operation Manual Index-1IndexAAudioBreakaway Audio 2-45Embedded Audio Source 2-45Ratio Control 2-48Ratio Profiles 2-50Audio Cont

Index-2 MMCP Installation/Operation ManualIIP addressdefault 1-8, 1-10determining 1-8setting 1-8KKeycut 2-26Matte Default 2-28modifier buttons 2

MMCP Installation/Operation Manual Index-3Transition Matteadjusting 2-33configuring 2-33Transition Rate buttons 2-13Transitions 2-12custom 2-12,

Index-4 MMCP Installation/Operation Manual

MMCP Installation/Operation Manual 1-1 Section 1 Installation Introduction This section gives installation and configuration instructions for the Gra